• Skip to primary navigation
  • Skip to main content
  • Skip to primary sidebar

The Woodgineer logo

  • Contact Us
  • Home
  • My Tools & Supplies
  • Commissions
  • About

walking stick (product category)

Making a Walking Stick

June 28, 2021 by The Woodgineer Leave a Comment

This video is dedicated to my dad on his 70th birthday and I have a guide below explaining the whole process of how I made this walking stick for him.

I’m making him a walking stick as he enjoys walking but due to an old injury struggles a little so I thought this might help.

And since I mentioned his age and frailties, he can also use it to beat me with!

For this project you will need:

  1. A stick – hazel, ash or any strong wood works well
  2. Some buffalo horn pre-shaped – I’m using a pistol grip style
  3. A bone disc – not vital but will make the handle look much nicer
  4. Threaded bar – I’m using 8mm
  5. Brass ferrule for the end of the stick
  6. Epoxy
  7. Sandpaper – multiple grits
  8. Abrasive paste

I started by sanding the end of the pre-shaped buffalo horn flat. I wasn’t too worried about a fine finish here as this is where the glue would go so I just used 180 grit sandpaper.

The Pre-shaped Buffalo Horn
Sanding the Buffalo Horn

I then marked a centre point with my centre finder, set the drill depth about 30mm and drilled a small hole for the 8mm threaded rod that will connect this to the stick.

Marking a centre point on the horn

I then took the (presumably human?) bone and sanded it flat and the two ends parallel to each other and again marked the centre but this time drilled the hole straight through it.

I then marked with a pencil where the bone and horn meet and slowly shaped the bone down to size with my bench sander.

Sanding the bone to size

The hazel stick I had to grow so I used some hazelnut chocolate, dirt and water and a few magic words…

Growing the Hazel stick

Once grown I tested the ideal height using me as reference since I’m about the same height as my dad.

I then cut the stick to the size accounting for the rough size of the handle and then marked the centre of the end of the stick.

Checking the height of the stick

I then drilled a pilot hole to make sure the hole lined up correctly (I’ve been burnt by this before!) and finally a larger hole for the threaded rod.

Drilling a pilot hole for the threaded rod

I then double-checked the handle would match up with the stick, sanding and shaping the bone and horn further until it was a perfect fit.

The other end of the stick needed a ferrule to protect it so I did a test fit and whittled down so it fitted snuggly.

Once happy I mixed up some 5 minute epoxy and glued the ferrule onto the end of the stick ensuring any excess was wiped off quickly. Its better to do this now than later ones its dried!

Glueing up the end of the stick to fit the ferrule

While the glue was out I turned to the parts of the handle and glued them together. To ensure everything was a really tight fit I put clamping force on the threaded rod with my vice and a separate wing nut onto the bone spacer.

Once properly dried I did some final shaping of the head piece to ensure it matched the stick then sanded up the grips with 120, 240 and finally 400 grit sandpaper. In hindsight I should have used more grit sizes in between to hide the toolmarks as this made the final sand extremely long.

Sanding up the grits

I then put on some Yorkshire grit, an abrasive paste that I normally use for woodturning. Its amazing stuff though and worked into the piece it gives you a wet sand that doesn’t get dust everywhere plus the particles in it break down to give you finer and finer sand as you go on. I wipe it off when done leaving something fairly polished without doing actual polishing.

Polishing the horn with Yorkshire Grit

I last check to see it fits and then I add epoxy to the thread rod and glue the head onto the stick.

Drizzling Epoxy onto stick

The bark I wanted to leave on as this helps protect the stick, just as it once did while the tree was growing. Plus it looks fantastic.

A special mix of 1 part linseed 1 part tung 1 part mineral spirits was mixed up and I put on 3-4 coats with 24 hours between coats lightly with lint-free cloth.

Putting the finish onto the stick

Teak oil works too instead of Tung and I can say since its nearly 2 years since he’s had the stick, its held up extremely well.

My dad absolutely loved it!

The stick (sorry to ruin the magic), ferrule, bone and handle were purchased from the awesome Keith Pickering and not actually grown. If you want to make one please check out his stuff at:
http://www.thestickman.co.uk

This is my first walking stick but I’ve developed a taste for it so please let me know if you’re interested in seeing more! Maybe next time I’ll hand carve something interesting for the handle.

Final stick

Please subscribe and hit notify to be updated when I release new videos and constructive advice/feedback/ideas are all welcome in the comments below or on the video.

Also find me in these internety places:
https://twitter.com/thewoodgineer
https://www.facebook.com/TheWoodgineer
https://instagram.com/woodgineer
https://www.patreon.com/thewoodgineer
thewoodgineer@gmail.com

Thanks all!

Filed Under: Projects, Walking Sticks, Woodworking, YouTube Videos Tagged With: amazing walking sticks, bone, carving a walking stick, hazel, hiking, hiking stick, how to make, how to make a self defence walking stick, how to make a simple walking stick, how to make a walking cane, how to make a walking stick, knob stick, making, making a cane, making a walking stick, prince of wales knob, stick, walking, walking cane, walking staff, walking stick, walking stick (product category), walking sticks

Primary Sidebar

contact@thewoodgineer.com

New tools from those lovely people at @worxuk just New tools from those lovely people at @worxuk just in time for a bank holiday weekend and a long list of DIY stuff.
Obviously I’ll be using these in my videos too and there are some fun ones coming soon™️
Thanks Worx! 🥰
#worxtools #newtools #tools #diy
Buying a house? Completed it mate! Few months ag Buying a house?  Completed it mate!
Few months ago we thought we’d had the rug pulled out from under us as our landlord wanted to sell.  The home we’d made (not to mention my workshop) that we eventually wanted to buy was in a perfect location and somewhere we could happily spend the rest of our lives.
Thanks to some hard work by my lovely wife and help from family we’ve managed to convince the bank we’re responsible people (I know right? 😂) and get a mortgage.
Today it’s all ours along with the security that comes with not renting and we’re already pondering all the things we can do to it.
(And yes, workshop expansion is on the list there somewhere)
#generationrent #home #homeownership
Amazing time checking out the bunker at both @make Amazing time checking out the bunker at both @makerscentral and then for reals!
#tunnel #bunker #colinfurze #makercommunity #makerscentral
After an amazing weekend at @makerscentral I spent After an amazing weekend at @makerscentral I spent a crazy fun day with this bunch feeling totally out of place and the odd one out with my little YT channel.
Then after getting to know them all, perhaps bonding over near death experiences at @realcolinfurze workshop I realised we are all the odd ones and they are just simply amazingly nice people 🥰
Thanks again to Colin and your misses for hosting, the workshop and tunnel tour as well as playing with the cool toys and thanks to everyone for making feel like part of the fam especially @xrobotsuk for bringing me 😎
#tunnel #colinfurze #makercommunity #maker
Has been an absolute pleasure to see lots of frien Has been an absolute pleasure to see lots of friends old and new at @makerscentral this weekend! 🥰 apologies if I didn’t get a chance to see anybody!
Also massive thanks to the @vectricltd team for having me on their stand and all the love they give out to the maker community.  It’s been fun chatting to people there all weekend about CNCs and playing with the @onefinitycnc machine. (Though it did feel like cheating on my lovely @ooznest workbee but you know, different postcode….)
#cnc #makerscentral #mc23 #ooznest #vectric #onefinitycnc #makercommunity
On the @vectricltd stand today at @makerscentral r On the @vectricltd stand today at @makerscentral ready to meet anybody who wants to talk about their amazing software or about how a CNC machine just fits into my workshop and making.
#vectric #cnc #mc23 #makerscentral
On way to @makerscentral hooooo! #makerscentral On way to @makerscentral hooooo! 
#makerscentral
Day 12 of May for Makers “Favourite Part” He Day 12 of May for Makers “Favourite Part” 
Hehe.  I'll behave 😉
My favourite projects are ones that combine woodworking with electronics and the "brains" of most of them is an arduino specifically an ESP8266.  These tiny modules are cheap (as little as £2), have enough pins for most things you want to connect and even have onboard wifi!
Coding on them is just like any normal Arduino and 32kb of memory is more than enough for simple projects so whatever you can think of, you can connect to wifi.  Pot plants, cat flaps, toasters, pillows you name it….
ESP8266 ALL THE THINGS!
#mayformakers #mayformakers2023 #makersmovement #mfm23 #arduino #esp8266
Day 11 of May for Makers “Happy Accident” I m Day 11 of May for Makers “Happy Accident”
I made about 12 hexagon shaped bug hotels from recycled materials (mostly from my daughters old bed and pallet wood) but when you add up the time it takes to make them, you are looking at a price of £30 each if you want to make any kind of money so unsurprisingly these have never sold well at craft fairs.
But…wait… whats this?  They are just about the right size for an automata I'm currently working on and potentially could be used for others! 
Nice shape, recycled materials and a big open part so you can see the mechanism.
Score!
#mayformakers #mayformakers2023 #makersmovement #mfm23 #automata
Load More... Follow on Instagram

Recent Posts

  • Worx Maker X Review – WX988
  • Making a Walking Stick
  • Can I Convert a 3D Printer into a CNC?
  • Stick Family
  • Making a 3D Printed Animated GIF

Copyright © 2023 My Wordpress on the Foodie Pro Theme